| VR6 cam locking plate | ||||
 |
This precision machined tool locks both camshafts at top dead center for setting valve timing. Works for all 12 valve VR6 engines. | Precision machined from solid steel with a protective zinc finish. | $22.00 | |
| 12 point triple-square bit, 10mm size. ***Non-impact*** | ||||
 |
12 point triple-square drive bit - For head bolts and starter bolts on some models. This is not a Torx bit, it is a 12-point star shaped bit correct for these bolts. | 10mm size - for some starter bolts and AEB/ATW code 1.8T head bolts | $12.60 | |
| 12 point triple-square bit, 12mm size. 1/2 inch drive. ***Non-impact** | ||||
 |
12 point triple-square drive bit - For head bolts on some models. This is not a Torx bit, it is a 12-point star shaped bit correct for these bolts. | 12mm size, for many VW/Audi head bolt applications. | $12.60 | |
| 6 point poly-drive head bolt tool. ***Non-impact*** | ||||
 |
6 point poly-drive head bolt tool. 1/2 inch drive. | Required to remove and install head bolts on most late model VW/Audi engines. | $18.00 | |
| Extended spark plug socket - Removes 5/8 inch spark plugs. | ||||
 |
Spark plug socket, fits 5/8 inch spark plugs. Internal magnet holds plug in place. | 5/8 inch socket, 5 inch length, 3/8 inch internal square drive or 3/4 inch external hex drive. | $14.95 | |
| Offset O2 sensor wrench | ||||
 |
Offset O2 sensor wrench - Compact size and crows-foot design allow it to fit into confined areas and around obstacles. For all 2 1/8 | $24.95 | ||
| Flex-head O2 sensor wrench, 7/8 inch. | ||||
 |
Flexible O2 sensor wrench | Flexible head allows the wrench to fit into confined areas with tough angles. | $29.95 | |
| Timing belt tensioner tool | ||||
 |
Timing belt tensioner tool - Allows tensioning of eccentric idler pulley with pin holes. Grips center of pulley while allowing clearance for a wrench on the locking nut. Heat treated steel construction with a soft grip handle. | $19.43 | ||
| Compact 3-way timing belt tensioner tool | ||||
 |
Compact 3-way timing belt tensioner tool - Allows tensioning of eccentric idler pulley with pin holes. Fits nearly all VW/Audi timing belt tensioners, gas or diesel. 3-way design is ideal for engines with limited room between engine mount and tensioner. Grips center of pulley while allowing 360 degree access to tensioner and clearance for a wrench on the locking nut. Machined from 1-piece forged steel. Includes light duty 13mm flat wrench, lanyard and vinyl grip. | $39.00 | ||
| Adjustable cam locking bar for 2.8L V6. | ||||
 |
Cam locking tool kit- Holds camshafts at T.D.C. while replacing timing belt. Includes crankshaft locking pin. | Fits 98-05 Passat with 30V V6 engine. | $179.95 | |
| Universal sprocket counterhold wrench. | ||||
 |
Universal sprocket counterhold wrench - Essential for holding sprocket or pulley still while loosening or tightening center bolts. | Fits any sprocket or pulley with holes, including camshaft, intermediate shaft and injection pump sprockets. | $43.00 | |
| Power steering pump pulley holder | ||||
 |
Water pump and steering pump pulley holder - Holds power steering or water pump pulley from rotating while removing or replacing the three socket head bolts. | Works on power steering and water pump pulleys on all '75-current VW/Audi 4 cyl and VR6 engines. | $28.49 | |
| Bosch CIS fuel injector puller | ||||
 |
Bosch CIS fuel injector puller - Easily removes fuel injectors without stressing fuel lines. Pulls on the injector body, not the line. Works on most 8V CIS and CIS-E models by using a screwdriver as a lever. | Can be adapted to VW 16V models CIS-E and Motronic models as well | $9.62 | |
| Valve seal removal pliers | ||||
 |
Valve seal removal pliers - Narrow design allows access to valve stem seals even in the tight confines of 4 valve per cylinder heads. Features serrated tips for a positive grip on the seal, heat-treated steel construction and cushioned handles. | $43.00 | ||
| Valve spring compressor | ||||
 |
Valve spring compressor - To remove and install valve springs on most 4, 5 and 6 cyl models | We also rent this tool - please inquire. | $149.00 | |
| 36mm oil filter housing socket | ||||
 |
Oil filter housing socket , 36mm. Shallow socket used to remove oil filter housing cap | Used to remove oil filter housing cap on 2.0L 4 cyl Turbo FSI engines, and 2.8L VR6 engines. | $10.00 | |
| Oil filter housing drain tool | ||||
 |
Oil filter housing drain tool - Threads into the bottom of the oil filter housing to release the drain valve. Includes tube for easy draining. | Required to drain oil filter housing on all 2.0L 4 cyl Turbo FSI engines and 2.5L 5 cyl engines. | $35.00 | |
| Wrench, oil filter. 14 sided, 74mm across flats. | ||||
 |
Wrench, oil filter. 14 sided, 74mm across flats. 3/8 inch square drive. | Fits many spin-on oil filters as well as some plastic oil filter housing caps. Measure your filter or cap to ensure proper fit. | $14.75 | |
| Oil filter removal pliers, adjustable. | ||||
 |
Oil filter pliers, adjustable - Adjustable to fit a variety of oil filter sizes, steel jaws for easy filter removal and cushioned grips for comfort. | For use on spin-on type filters. | $14.95 | |
Facebook© 2012 GermanAutoParts.com